Amplifiers
The amplifiers are used to amplify the audio signal for driving the loudspeakers
TOPSELLER
Skip product gallery
Topseller
DAP HP 900 2x 350 W/8 Ohm Amplifier
€415.00*
The DAP HP-900 is a powerful and safe amplifier with bridge, parallel and stereo modesClass AB amplifierMetal housingColor: grayEfficient forced air coolingFull protection circuitsIP rating: IP20 (indoor use only)19"/2U designOutput per channel at 8 ohms from 20 Hz - 20 kHz: 350 WOutput per channel at 4 ohms from 20 Hz - 20 kHz: 450 WBridge output at 8 ohms from 20 Hz - 20 kHz: 900 WOutput channels: 2Output gain: 32 dBOutput mode: Bridge, Parallel, StereoOutput connector: 4-pin speaker connectorInputs:Mono inputs: 2Mono input connector: 3-pin XLRBalanced mono input Sensitivity: 1 dBuAudio specificationsTHD level: < 0.5 %Signal-to-noise ratio: > 100 dBSlope: 13 V/µsAmplifier technology: Class ABAttenuation factor: 100:1Overlay: 75 dBuFrequency response minimum: 10 HzFrequency response maximum: 20000 HzDimensions: (HxWxD): 88 x 483 x 310 mmInstallation depth (without plug): 310 mmWeight: 10.6 kg
delivery time 14 days
DAP HP 500 2x 150 W/8 Ohm Amplifier
€315.00*
The DAP HP-500 is a powerful and safe amplifier with bridge, parallel and stereo modesClass AB amplifierMetal housingColor: grayEfficient forced air coolingFull protection circuitsIP rating: IP20 (indoor use only)19"/2U designOutput per channel at 8 ohms from 20 Hz - 20 kHz: 150 WOutput per channel at 4 ohms from 20 Hz - 20 kHz: 200 WBridge output at 8 ohms from 20 Hz - 20 kHz: 400 WOutput channels: 2Output gain: 32 dBOutput mode: Bridge, Parallel, StereoOutput connector: 4-pin speaker connectorInputs:Mono inputs: 2Mono input connector: 3-pin XLRBalanced mono input Sensitivity: 1 dBuAudio specificationsTHD level: < 0.5 %Signal-to-noise ratio: > 100 dBSlope: 10 V/µsAmplifier technology: Class ABAttenuation factor: 100:1Overlay: 75 dBuFrequency response minimum: 10 HzFrequency response maximum: 20000 HzDimensions: (HxWxD): 88 x 483 x 310 mmInstallation depth (without plug): 310 mmWeight: 8,7 kg
delivery time 14 days
Linea Research 48 M20 8 channel amplifier
€7,919.00*
8-channel Class-D high-performance amplifier with switched-mode power supply8 x 1500W / 2 ohms, 8 x 2500W / 4 ohms, 8 x 1500W / 8 ohms4 x 3000W / 4 Ohm, 4x 5000W / 8 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 8 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 14 days
DJP-900P MK2 Class D Amplifier 2x 460W
€349.00*
The compact stereo mixing amplifier DJP-900P with efficient class D output circuitry is particularly suitable for permanent installations in restaurants, gyms and retail locations which require quick-access music playback control. It provides 2 x 460 watts at 4 ohms and makes mixing of a stereo line source and a microphone easy.For double output power it is possible to switch to bridge mode. Then 900 watts are provided.Low-impedance speakers and PA speakers with 100 V audio transformers can be connected. Stream your music wirelessly from your smartphone, tablet or computer via Bluetooth to the built-in audio player, which also offers slots for USB storage devices and SD(HC) memory cards. Extensive protective circuits provide protection e.g. against short circuit, overload and overheating.Output power: 2 x 460 W RMS (4 ohms)2 x 240 W RMS (8 ohms)Max. 260 W bridged (100 V)Max. 900 W bridged (8 ohms)
delivery time 14 days
Linea Research 44 M20 Dante 4 channel amplifier with on-board DSP with Dante
€7,390.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 7 days
Linea Research 44 M06 4 channel amplifier
€4,799.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 1500W / 2 ohms, 4 x 1500W / 4 ohms, 4 x 1500W / 8 ohms2 x 3000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 7 days
Linea Research 44 M10 4 channel amplifier
€5,690.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 2500W / 2 ohms, 4 x 2500W / 4 ohms, 4 x 1500W / 8 ohms2 x 5000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 7 days
Linea Research 44 M06 Dante 4 channel amplifier with on-board DSP with Dante
€5,599.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 1500W / 2 ohms, 4 x 1500W / 4 ohms, 4 x 1500W / 8 ohms2 x 3000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 7 days
QPRO Audio 4 channel amplifier 1HE 4 x 3000W/2Ohm
€2,299.00*
The - eries amplifiers are -QLP S digital four channel amplifiers with power factor correction technology.All QLP models have a very high-efficient switch mode power supply, which ensures best and stableperformance even at full power.Our digital amplifier msv technology, together with the use of best selected electronic components allows the 2 Ohmuse of all four channels at same time with a maximum power of 4 x 3000 watts, packed in a lightweight andcompact size of 1U.The QLP-Series is equipped with a switch msv on the back panel to adjust the Input gain to 29dB, 32dB, 35dB and38dB to match with other devises.Four SPEAKON outputs are mounted at the rear side. The SPEAKON connector of the output channel A (1+/1-) isconnected with all four poles and offers the output signal of channel B at the pins 2 (+/-). Channel C + D isequipped with the same wiring. This four-pole connection makes it easy to connect a Sub / Sat system with onecable only.The QLP-Series can be switched into msv stereo, mono and bridge mode. In mono mode the input signal fromchannel A is linked to the output channel A + B, and input C is linked to output C + D. In bridget mode theconnection is 1+/2- on output A and output C. The Clip limiter can be switched On/Off on all channels.Rated Output Power (THD + N= 1%, 1KhZ contiune sine wave, all channel driving): 8 Ohm / Stereo: 4 x 1000W4 Ohm / Stereo: 4 x 1700W2 Ohm / Stereo*: 4 x 3000W16 Ohm / Bridge: 2 x 2000W8 Ohm / Bridge: 2 x 3400W4 Ohm / Bridge*: 2 x 5780WOutput RMS voltage (THD+N=1%,1kHz): 89,4VSlew rate (1kHz, Low-pass filter msv bypassed): 50V7usSensitivity (Rated Power, 1kHz): Selectable 38dB, 35dB, 32dB, 29dBTHD+N(10% Rated Power, typical): 0,01%IMD-SMPTE(10% Rated Power,typical): 0,01%DIM30(10% Rated Power, typical): 0,01%Cross-talk(20Hz-1kHz,below Rated Power): >=90dBFrequency response(10% Rated Power,20Hz-20kHz,8Ohm): +-0,2dBInput impedance: 20k Ohm (Balance), 10kOhm (unbalance)Damp factor(8Ohm,20Hz-200Hz): >=5000SNR(A weighted 20Hz-22kHz): >=107dBMain power: 90 - 260 VAC, 50-60HzProtection: Under voltage, msv DC, Over temperature, Over load limiter, Short protection.Size(W×H×D): 483x45x370mmNet weight: 9kg*Test condition: 20ms,1kHz,THD+N=1%.
delivery time 7 days
Linea Research 44 M10 Dante 4 channel amplifier with on-board DSP with Dante
€6,490.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 2500W / 2 ohms, 4 x 2500W / 4 ohms, 4 x 1500W / 8 ohms2 x 5000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
delivery time 7 days
Yamaha Px5 Amplifier - 2x 500watts/8ohm
€899.00*
Yamaha PX5Power:2 x 800 W / 4 Ohm,2 x 500 W / 8 Ohm,1 x 800W 8 Ohm Bridge,1 x 1400W 4 Ohm BridgeSpeaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 6.9 kg
Immediately available or ready for collection
Crown XLS XLS 2502 Amplifier 2x 775 Watt/4 Ohm
€659.00*
CROWN XLS 2502 digital amplifier with class D amplifier circuit2x 1.200 watts @ 2 ohms2x 775 watts @ 4 ohms2x 440 watts@ 8 ohmsbridged 1x 2.400 watts @ 4 ohms, monobridged 1x 1.550 watts @ 8 ohms, monoHigh and low pass filter per channelSleep mode with external triggerPeakX limiterVery silent, temperature-dependent fanDamping factor> 2001.4 and 0.775 volts input sensitivityInputs: XLR, Jack, RCA per channelOutputs: Speakon, screw terminals per channelHeight: 2UDepth: 27.2 cm4.9 kgTop Features:New is the energy management. Due to recovering energy the Crown XLS amplifier operates very efficiently. Therefore it is more efficient than conventional amplifiers. Another new feature is the sleep mode and a power trigger for external switch on and off.The large display shows clearly all parameters. The Blackout function, new menus and lockout mode make the operation easy and safe.
Immediately available or ready for collection
Crown XTi 1002 Amplifier 2x 500 Watt/4 Ohm
€539.00*
Crown Xti 1002, DSP control amplifier, 19" 2 U, 2x 700 W (2 Ohm), 500 W (4 Ohm), 275 W (8 Ohm), 1000 W Bridge 8 Ohm, 1400 Watt Bridge 4 Ohm, DSP-Control: Input EQ with 6 parametric Filters per channel with adjustable Q-Shelf and +/- 15 dB Gain, Crossover with High- and Lowpass, per channel with 6/12/18/24 dB per Octave and switchable polarity, Output EQ with 8 parametric Filters per channel with adjustable Q-Faktor and +/- 15 dB Gain, Delay up to 50 ms, Subharmonic Synth, Peak Plus Limiter with adjustable Threshold, Attack and Release, 50 Presets, 3 mode switchable cooling fan, HiQnet Band Manager and System Artchitect Software control by USB-Port Type B, display with temperature of powersupply and voltage, 2x NL 4 Speakon out, Binding Post out, XLR in/out, dimensions: 19" (485mm) x 2 U (89mm) x 311 mm, weight 8,4 Kg
Immediately available or ready for collection
Linea Research 44 M20 4 channel amplifier
€6,599.00*
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK
Immediately available or ready for collection
Linea Research ASC48 Dante Card
€799.00*
Linea Research ASC48 Dante Card
Immediately available or ready for collection
Yamaha Px10 Amplifier - 2x 1000watts/8ohm
€1,130.00*
Yamaha PX10Power:2 x 1200 W / 4 Ohm,2 x 1000 W / 8 Ohm,Speaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 7,4 kg
Immediately available or ready for collection
QPRO Audio 4 channel amplifier 1HE 4 x 600W/8Ohm
€1,049.00*
The QLE series amplifiers are 2 or 4 channel amplifiers.All models have a highly efficient switching power supply, which ensures that QLE amplifiers run optimally and stably even at full power.Our digital amplifier technology, msv combined with the use of the best selected electronic components, enables 4 ohms to be used simultaneously on all two or four channels with maximum performance. Packed in a lightweight and compact 1U size.The QLE series is equipped with a switch on the back to adjust the input sensitivity of 0.7 V or 1 V.Nominal output power (THD + N = 1%, msv continue 1 kHz sine wave, control all channels)Rated Output Power(THD+N= 1%,1kHz continue sine wave, all channel driving)8Ohm Stereo: 4x600W4Ohm Stereo: 4x900W16Ohm Bridge: 2x1200W8Ohm Bridge: 2x1800WOutput RMS voltage: 693VSensitivity: 1 Vrms , 0.7 Vrms (msv Rated Power,1kHz)THD+N: 0.05% (10% Rated Power, typical)Cross-talk: >=75dB (20Hz-1kHz,below Rated Power)Frequency response: +-0.2dB (10% Rated Power,20Hz-20kHz,8 )Input impedance: 20k Balance 10k UnbalanceDamp factor: >=1000(8Ohm ,20Hz-200Hz)SNR: >=100dB(A weighted 20Hz-20kHz)Main power: 220VAC 10 (+- % )50/60HzProtection: Under voltage, DC, Over msv temperature, Over load limiter, Short protection.Size(W×H×D): 480x45x352mmNet weight: 6,8kg
Immediately available or ready for collection
QPRO Audio 2 channel amplifier 1HE 2 x 800W/8Ohm
€879.00*
The QLE series amplifiers are 2 or 4 channel amplifiers.All models have a highly efficient switching power supply, which ensures that QLE amplifiers run optimally and stably even at full power.Our digital amplifier technology, msv combined with the use of the best selected electronic components, enables 4 ohms to be used simultaneously on all two or four channels with maximum performance. Packed in a lightweight and compact 1U size.The QLE series is equipped with a switch on the back to adjust the input sensitivity of 0.7 V or 1 V.Nominal output power (THD + N = 1%, continue 1 kHz sine wave, control all channels)Rated Output Power(THD+N= 1%,1kHz continue msv sine wave, all channel driving)8Ohm Stereo: 2x800W4Ohm Stereo: 2x1200W16Ohm Bridge: 1x1600W8Ohm Bridge: 1x2400WOutput RMS voltage: 80.0VSensitivity: 1 Vrms , 0.7 Vrms (Rated Power,1kHz)THD+N: 0.05% (10% Rated Power, typical)Cross-talk: >=75dB (20Hz-1kHz,below Rated Power)Frequency response: +-0.2dB (10% Rated msv Power,20Hz-20kHz,8 )Input impedance: 20k Balance 10k UnbalanceDamp factor: >=1000(8Ohm ,20Hz-200Hz)SNR: >=100dB(A weighted 20Hz-20kHz)Main power: 220VAC 10 (+- % )50/60HzProtection: Under voltage, DC, Over msv temperature, Over load limiter, Short protection.Size(W×H×D): 480x45x352mmNet weight: 5,9kg
Immediately available or ready for collection
