4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

Linea Research 44 M Dante Card

Linea Research ASC48 Dante Card

The QLP - Series amplifiers are digital two channel amplifiers with power factor correction technology.All QLP models have a very high-efficient switch mode power supply, which ensures best and stableperformance even at full power.Our digital amplifier msv technology, together with the use of best selected electronic components allows the 2 Ohmuse of all four channels at same time with a maximum power of 2 x 4760 watts, packed in a lightweight andcompact size of 1U.The QLP-Series is equipped with a switch msv on the back panel to adjust the Input gain to 29dB, 32dB, 35dB and38dB to match with other devises.Four SPEAKON outputs are mounted at the rear side. The SPEAKON connector of the output channel A (1+/1-) isconnected with all four poles and offers the output signal of channel B at the pins 2 (+/-). This four-pole connection makes it easy to connect a Sub / Sat system with onecable only.The QLP-Series can be switched into msv stereo, mono and bridge mode. In mono mode the input signal fromchannel A is linked to the output channel A + B. In bridget mode theconnection is 1+/2- on output A. The Clip limiter can be switched On/Off on all channels.Rated Output Power (THD + N= 1%, 1KhZ contiune sine wave, all channel driving): 8 Ohm / Stereo: 2 x 1000W4 Ohm / Stereo: 2 x 1700W2 Ohm / Stereo*: 2 x 4760W16 Ohm / Bridge: 1 x 2000W8 Ohm / Bridge: 1 x 3400W4 Ohm / Bridge*: 1 x 5780WOutput RMS voltage (THD+N=1%,1kHz): 89,4VSlew rate (1kHz, Low-pass filter msv bypassed): 50V7usSensitivity (Rated Power, 1kHz): Selectable 38dB, 35dB, 32dB, 29dBTHD+N(10% Rated Power, typical): 0,01%IMD-SMPTE(10% Rated Power,typical): 0,01%DIM30(10% Rated Power, typical): 0,01%Cross-talk(20Hz-1kHz,below Rated Power): >=90dBFrequency response(10% Rated Power,20Hz-20kHz,8Ohm): +-0,2dBInput impedance: 20k Ohm (Balance), 10kOhm (unbalance)Damp factor(8Ohm,20Hz-200Hz): >=5000SNR(A weighted 20Hz-22kHz): >=107dBMain power: 90 - 260 VAC, 50-60HzProtection: Under voltage, msv DC, Over temperature, Over load limiter, Short protection.Size(W×H×D): 483x45x370mmNet weight: 9kg*Test condition: 20ms,1kHz,THD+N=1%.

4-channel Class-D high-performance amplifier with switched-mode power supply4 x 2500W / 2 ohms, 4 x 2500W / 4 ohms, 4 x 1500W / 8 ohms2 x 5000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

The - eries amplifiers are -QLP S digital four channel amplifiers with power factor correction technology.All QLP models have a very high-efficient switch mode power supply, which ensures best and stableperformance even at full power.Our digital amplifier msv technology, together with the use of best selected electronic components allows the 2 Ohmuse of all four channels at same time with a maximum power of 4 x 3000 watts, packed in a lightweight andcompact size of 1U.The QLP-Series is equipped with a switch msv on the back panel to adjust the Input gain to 29dB, 32dB, 35dB and38dB to match with other devises.Four SPEAKON outputs are mounted at the rear side. The SPEAKON connector of the output channel A (1+/1-) isconnected with all four poles and offers the output signal of channel B at the pins 2 (+/-). Channel C + D isequipped with the same wiring. This four-pole connection makes it easy to connect a Sub / Sat system with onecable only.The QLP-Series can be switched into msv stereo, mono and bridge mode. In mono mode the input signal fromchannel A is linked to the output channel A + B, and input C is linked to output C + D. In bridget mode theconnection is 1+/2- on output A and output C. The Clip limiter can be switched On/Off on all channels.Rated Output Power (THD + N= 1%, 1KhZ contiune sine wave, all channel driving): 8 Ohm / Stereo: 4 x 1000W4 Ohm / Stereo: 4 x 1700W2 Ohm / Stereo*: 4 x 3000W16 Ohm / Bridge: 2 x 2000W8 Ohm / Bridge: 2 x 3400W4 Ohm / Bridge*: 2 x 5780WOutput RMS voltage (THD+N=1%,1kHz): 89,4VSlew rate (1kHz, Low-pass filter msv bypassed): 50V7usSensitivity (Rated Power, 1kHz): Selectable 38dB, 35dB, 32dB, 29dBTHD+N(10% Rated Power, typical): 0,01%IMD-SMPTE(10% Rated Power,typical): 0,01%DIM30(10% Rated Power, typical): 0,01%Cross-talk(20Hz-1kHz,below Rated Power): >=90dBFrequency response(10% Rated Power,20Hz-20kHz,8Ohm): +-0,2dBInput impedance: 20k Ohm (Balance), 10kOhm (unbalance)Damp factor(8Ohm,20Hz-200Hz): >=5000SNR(A weighted 20Hz-22kHz): >=107dBMain power: 90 - 260 VAC, 50-60HzProtection: Under voltage, msv DC, Over temperature, Over load limiter, Short protection.Size(W×H×D): 483x45x370mmNet weight: 9kg*Test condition: 20ms,1kHz,THD+N=1%.

4-channel Class-D high-performance amplifier with switched-mode power supply4 x 1500W / 2 ohms, 4 x 1500W / 4 ohms, 4 x 1500W / 8 ohms2 x 3000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

4-channel Class-D high-performance amplifier with switched-mode power supply4 x 2500W / 2 ohms, 4 x 2500W / 4 ohms, 4 x 1500W / 8 ohms2 x 5000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

4-channel Class-D high-performance amplifier with switched-mode power supply4 x 1500W / 2 ohms, 4 x 1500W / 4 ohms, 4 x 1500W / 8 ohms2 x 3000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

The QLE series amplifiers are 2 or 4 channel amplifiers.All models have a highly efficient switching power supply, which ensures that QLE amplifiers run optimally and stably even at full power.Our digital amplifier technology, msv combined with the use of the best selected electronic components, enables 4 ohms to be used simultaneously on all two or four channels with maximum performance. Packed in a lightweight and compact 1U size.The QLE series is equipped with a switch on the back to adjust the input sensitivity of 0.7 V or 1 V.Nominal output power (THD + N = 1%, msv continue 1 kHz sine wave, control all channels)Rated Output Power(THD+N= 1%,1kHz continue sine wave, all channel driving)8Ohm Stereo: 4x600W4Ohm Stereo: 4x900W16Ohm Bridge: 2x1200W8Ohm Bridge: 2x1800WOutput RMS voltage: 693VSensitivity: 1 Vrms , 0.7 Vrms (msv Rated Power,1kHz)THD+N: 0.05% (10% Rated Power, typical)Cross-talk: >=75dB (20Hz-1kHz,below Rated Power)Frequency response: +-0.2dB (10% Rated Power,20Hz-20kHz,8 )Input impedance: 20k Balance 10k UnbalanceDamp factor: >=1000(8Ohm ,20Hz-200Hz)SNR: >=100dB(A weighted 20Hz-20kHz)Main power: 220VAC 10 (+- % )50/60HzProtection: Under voltage, DC, Over msv temperature, Over load limiter, Short protection.Size(W×H×D): 480x45x352mmNet weight: 6,8kg