Art MX225 5-zone installation MixerYou want to use multiple amplifiers or active monitors in a single installation? Then the ART MX 225 is the correct amplifier. With this installation you can spend mixer 2 stereo sources from each of the five output zones. So perfect for every bar, bistro each and every event in which several rooms to be provided with music.equipment2 inputs - mono or StrereoAll inputs can be assigned to each zone - at the same timeBalanced XLR outputsStereo / Mono switch on each outputMono indicator LED5 LED level meters (-25, -20, -15, -10, clip).

The Compact 8.1 is a high-quality 1U microphone line mixer for 19" racks. All inputs are suitable for microphones or as line-level inputs. They are all equipped with a high-pass filter and a phantom power selector switch. The mixer has a balanced master output, a record output and a monitor output. The monitor output can also be used as an independent additional output for a second area or zone. The main EQ has a mid-frequency sweep that allows you to eliminate your system's feedback frequency when using the Compact 8.1 as a microphone mixer. All channels are equipped with signal/clip displays, thanks to which you have a direct overview of your input signals even from a distance. The Compact 8.1 combines clear operation with a high number of inputs and intelligent functions in a 1U mixer. 8 combo mic/line inputs EQ with mid sweep phantom power Selectable high pass filter Power supply: 240VAC 50-60Hz Output voltage: 15VAC Power consumption: 12 W Power input plug: Low Voltage DC plug Weight: 2.2kg

8-channel audio mixer with matrixMatrix input assignment: 8 audio inputs are freely assignable to each of the 8 outputsDivision of the 8 outputs into 4 groups; each with separate level and pan control per channelUltra flexible configuration modes; distributes the signal of up to 8 audio sources to e.g. 8 mono zones or 4 stereo zones, each with a different output signalInputs and outputs via balanced XLR jacksRack installation, 2 UPower supply: 115/230 V, 50/60 Hz ~ Power consumption: 10 W Frequency range: 20-20000 Hz Dynamic range: 100 dB Max. input level: +21 dBU Input impedance: 10 kohm Max. gain: +12 dB, per channel Dimensions (WxDxH): 482 x 195 x 89 mm Weight: 3.5 kg

Convenient connections—plus a stereo Bluetooth channel—add true versatility.The Alesis MultiMix 10 Wireless is redefining the rackmount mixer category. Compact and complete, the MultiMix 10 Wireless delivers ten-channel mixing in a neat 3U package that is perfect for smaller clubs and venues, houses of worship, as well as mobile/traveling systems. The MultiMix 10 Wireless benefits from an array of easily accessible front panel jacks that enhance the versatility and usefulness of this generously equipped mixer. Topping off the feature list is a channel dedicated to receiving the stereo playback from any Bluetooth device. The MultiMix 10 Wireless is a new breed of rackmount mixer.All Are WelcomeThe MultiMix 10 Wireless provides a wealth of inputs to accommodate nearly any audio input. Channels 1-4 are ideal for vocals or acoustically mic’ed instruments, direct boxes, and more. Each provides an XLR mic input with available phantom power; a balanced 1/4" TRS line input, plus a TRS 1/4" insert jack for incorporating additional effects or working with a second mixer. Channels 5-8 have been set as stereo pairs, offering 1/4" left and right inputs. These channels are ideal for stereo sources such as a keyboard, electronic drum set, drum machine, external mixer, etc. Channels 7-8 also provide left and right RCA inputs.Wireless WonderStream a stereo audio signal from any Bluetooth device to Channels 9-10 of the MultiMix 10 Wireless. Single-button pairing keeps it simple. Now you can easily play music between sets, stream audio from a computer during a multimedia presentation, or even play a track from a patron’s smartphone for satisfying that “special request.” The articulating Bluetooth antenna delivers optimum reception.Jack AttackAn additional set of front panel jacks go above and beyond what most rack mixers offer to set your new MultiMix 10 Wireless mixer apart form the crowd in both convenience and functionality. No more snaking cables from front to back; no more reaching around and guessing; no more un-mounting the mixer to get at the jacks you need. To begin with, Channels 1 and 2 are equipped with XLR+1/4" combo inputs that override the rear jacks. Simply plug in a mic for making house announcements, adding a new source, patching in a sampler, or whatever you need. The stereo 1/8" external input allows instant access to the dedicated Bluetooth channel, providing a quick way to add in any stereo, handheld, or mobile device. Finally, the stereo 1/8" front panel output provides the master output signal—taken before the master fader—to deliver an efficient way to capture and record a live mix.Maximum MixingUsing the MultiMix 10 Wireless is easy and intuitive. Each single and stereo-paired channel offers a trim knob, peak LED, and a smooth-travelling 60mm fader for attaining the best signal level. In addition, there is a two-band EQ and pan for shaping the sound and creating a great mix. There are two aux send knobs per channel for creating a separate monitor mix, using an external global effect, etc. Aux 1 is set to pre-fader and Aux 2 is post-fader for maximum versatility.Dual multi-segment LED meters and a Master output fader allow you to easily monitor and control your levels. Left and right main outputs are equipped with balanced 1/4" TRS jacks—ideal for extended cable runs. The left and right monitor outs provide unbalanced 1/4" jacks. There is a separate headphone output on the front panel, with a dedicated volume control.Bluetooth is a registered trademark of Bluetooth SIG.FEATURESConvenient front panel jacks add versatilitySpace-saving 3U rackmount design is perfect for venues and mobile rigsBluetooth streaming with simple single-button pairingArticulating Bluetooth antenna for optimum reception4 high-gain mic/line preamps with inserts2-band high and low shelving EQ on every channel 
Pre-fader and post-fader aux sends; stereo aux returnCONTENTSMultiMix 10 WirelessPower SupplyQuickstart GuideSafety & Warranty ManualSPECSInputs:Channels 1-4 (mono):Mic: XLR with switchable phantom powerLine: 1/4" MonoInsert: 1/4" TRSFront: XLR+1/4" combo jacks(Channels 1 and 2 only—overrides rear jacks)Channels 5-6 (stereo pair):Line: 1/4" Left, RightChannels 7-8 (stereo pair):Line: 1/4" Left, RightRCA: Left, RightChannels 9-10 (stereo pair):Bluetooth: Stereo Streaming InExt: 1/8" Stereo (front panel)Aux Return: 1/4" TRS Balanced Left, RightOutputs:Main: 1/4" TRS Balanced Left, RightMonitor: 1/4" Left, RightAux Send 1: 1/4"Aux Send 2: 1/4"Headphones: Stereo 1/4"Ext: 1/8" Stereo (front panel)Design:3U Rackmount chassisDetachable power cableDimensions:Height: 5.25"Depth: 6.25"Width: 19"Weight: 8.9lbs

The ART MX524 Five Channel Four Zone Mic/Line Mixer is a versatile rack mount mixer that combines Five independent input channels and routes them to four zone outputs. Channels one thru four accept a balanced Line or Mic signal thru the Combo jack connector. CH5 accepts a line level signal through RCA jacks. The unit has an independent selectable +48 Volt phantom power function for channels one thru four. Channels one thru four can also accept unbalanced line-level signals. Each channel has a level control and can be routed to any zone output. Separate level, bass and treble controls adjust the sound of each input channel.The ART MX524 may be used on stage, in the studio, or for permanent install applications including conference rooms, corporate boardrooms, churches, restaurants, small clubs, health clubs and more. A built-in power supply and triple high 19-inch rack mount format allows for easy installation and reliable long-term operation.Key FeaturesFive input channels with individual level controls using XLR/Phono jacks with master level, bass and treble controlsBalanced Mic/Line XLR inputs for channels one thru fourFull +48V low-noise phantom power for channels one thru four mic inputsFront panel 1/8-inch stereo (TRS) mini-phone plug for Headphone monitoringFour sets of Euro Bloc connectors for the Zone outputsTelephone paging functionDc power back upSeparate monitor outputsLED VU meter on all outputsRear mount RCA Line inputs for additional audio inputsRugged 3U rack-mount steel chassis with built-in power supplyPerfect for stage, studio and permanent installationsThree-year warrantySpecificationsFrequency Response 20 Hz – 22kHz ± 2 dBMax. Input Gain: 60dB CH MIC. Input Main out (XLR, balanced)50dB CH MIC. Input & REC. out (unbalanced)60dB CH MIC. Input Mic. out (unbalanced)60dB CH MIC. Input Mono out (unbalanced)THD&N:

dbx ZonePro 640, programmable, digital DSP audio processor The programmable audio signal processor is installed in a 19" housing with 1U. It has two balanced microphone or line inputs and an additional 4 asymmetrical line inputs. There are 4 symmetrical line outputs available on the output side. All inputs and outputs are freely assignable. Each of the four outputs has an LED on the front for signal display. The device was operated via the front display. The controls on the device can be locked to prevent unintentional operation of the settings. Up to 12 remote control units can be addressed for preset, source selection and level. There is an RS-232 interface on the front and back. The rear socket can be connected to a media control system, and in parallel the device configurations can be carried out via a PC connected to the front. The included software must be installed on a computer to configure the device. This software should be able to configure system structures. Elements such as mixer matrix, feedback suppression, loudness, leveler, compressor, limiter, noise gating, notch filtering, bandpass and crossover, delay, parametric EQ etc. should be available. Once the device has been configured, it should be possible to operate the device without a connected computer. All parameters required for this are saved in non-volatile memory in the device. Characteristics: Inputs: 4x asymmetric line + 2x balanced microphone (with phantom power) - or line level Outputs: 4 balanced line outputs Dynamic range: 109dB A-weighted Sample rate: 48kHz / 24-bit oversampling Distortion: 0.003% typical at +4dBu, 1kHz Frequency response: 20Hz - 20kHz, +/- 0.5dB Crosstalk: 80dB Power consumption: 9 watts

DAP IMIX-7.37-channel 2U install mixer - 3 zonesThe DAP IMIX-7.3 is a compact installation mixer with zone control. It has exact the same functionality as the IMIX-7.1 but each input on the IMIX-7.3 can be routed to the desired output. This function makes it possible to control 3 areas with different music, sound level and EQ settings.Gain settings at backsideSpecial front input for phone/MP3 devicesZone control for 3 balanced outputs2 Mic, 11 Line inputsSpecificationsInputsMono Inputs: 2Mono Input Connector: 3-pin XLR, TRS balanced 6.3 mmStereo Inputs: 10Stereo Input Connector: RCAPhono Audio Inputs: 2Phono Audio Input Connector: RCAAuxiliary Inputs: 1Auxiliary Input Connector: RCA, TRS balanced 3.5 mmOutputsMain Outputs: 3Main Output Connector: 3-pin XLR, RCAHeadphone Output: 1Headphone Output Connector: TS balanced 6.3 mmRecord Output: 1Record Output Connector: RCAAudio SpecificationsTHD Level: < 0.05 %Signal-to-noise Ratio: > 100 dBFrequency Response Minimum: 20 HzFrequency Response Maximum: 20000 HzSound EditingMicrophone Input Equalizer Gain Range: 12 dBParametric Microphone Equalizer: 3 BandsMicrophone Input Fixed Frequencies: 80, 1.000, 12.000 HzParametric Main Equalizer: 3 BandsMain Output Equalizer Gain Range: 12 dBMain Output Fixed Frequencies: 80, 1.000, 12.000 HzProduct PropertiesLED Indicators: Channel select, Clip, Mute, Output level, SignalElectrical Specifications and ConnectionsPower Supply: 240 V AC 50-60 HzOutput Voltage: 18 V ACPower Consumption: 19.1 WPower Connector In: Low Voltage DC plugMechanical SpecificationsFader Length: 60 mmHeight (mm): 88 mmWidth (mm): 95 mmLength (mm): 481 mmFlightcase Size: 19"Rack Units: 2 UHousing: MetalColour: BlackWeight: 2.8 kgIP Rating: IP20 (indoor use only)Included ItemsIncluded Accessories: Adapter

The MZ-223 is a built-in mixer for permanent installation in shops, public facilities, restaurants, bars, theme parks or hotels. It is intended to provide three different rooms or zones with background music and announcements from different sources. Any of the seven input channels can be routed to any or all three output zones.The mixer offers five input channels for line-level signals from analog playback sources such as media players, radio receivers or cassette decks. Two channels can be switched to phono to connect turntables. All channels have their own input level controls, clipping LEDs and a fader. Two additional microphone input channels - with level controls, LED meters and 3-band equalization - are available for announcements, speech transmission, karaoke or other applications with dynamic microphones. If these are used for announcements, for example, the volume of the background music can be automatically reduced according to the microphone volume using the integrated talkover function.Each of the sum outputs for the three zones is equipped with a level control, LED level display and 3-band tone control. There is also an independent monitor output for the control room and a headphone output with level control for monitoring selected input channels (pre-fader) and the main outputs.Main features at a glanceBuilt-in mixers with multiple inputs that can be routed to multiple outputsFive stereo input channels for line signals (two switchable to phono) with gain controls, clipping LEDs and fadersTwo additional microphone input channels with level controls, three-band equalization and LED level metersMicrophone and line signals can be output mixedThe talkover function can automatically decrease the volume of background music according to the microphone levelThree zone outputs with level controls, three-band tone control and LED level metersSeparate stereo monitor outputHeadphone output with level control can be used for previewing (before the fader) selected input channels and monitoring the sum outputs19 inch installation housing with two height unitsTechnical specificationsaudio inputsMicrophone inputs 1-2Balanced: XLR-3-31 (1: Ground, 2: Hot (+), 3: Cold (-))Unbalanced: 1/4" phone jack, 3 poles (tip: hot (+), ring: cold (-), sleeve: ground) Input impedance: 33 kO Nominal input level: -65 dBu (VOLUME control at MAX), -30 dBu (VOLUME control at MIN)Line inputs (unbalanced)RCA sockets Nominal input level: -10 dBV Maximum input level: 10 dBV Input impedance: 22 kOaudio outputsSum outputs 1 and 2 (unbalanced)RCA jacks Nominal output level: -10 dBV Maximum output level: 6 dBV Output Impedance: 200 OSum outputs 1 and 2 (balanced)XLR-3-31 (1: Ground, 2: Hot (+), 3: Cold (-)) Nominal output level: 4 dBu Maximum output level: 24 dBu Output Impedance: 200 Omonitor outputsRCA sockets Nominal output level: -16 dBV Maximum output level: 0 dBV Output Impedance: 200 OHeadphone output: 1/4" stereo jack Maximum output power: 50mW + 50mW (at 32 O)Performance data audioFrequency Response: 20Hz - 20kHzDistortion: =0.03%Crosstalk attenuation: 65 dBpower supply and other datapower supplyAC adapter Tascam PS-M1524 (included) Input Voltage: AC 100-240V 50/60Hz Output Voltage: DC 15V Output Current: 2.4APower Consumption: 35WDimensions (W × H × D): 482mm × 88mm × 93mmWeight: 2.5kgPermissible operating temperature range: 5 - 35 °C

Extends every mixer with additional outputs2 stereo XLR inputs5 stereo zone XLR outputs Each zone with level controls for both inputs and mono switch LED display of signal input, distortion and mono/stereo modeRack installation with 1 U

The DAP IMIX-7.1 is an installation mixer with 7 channels and 3 master outputs. 19"/2U installation mixer Suitable for gastronomy, retail, public facilities and nightlife 2x microphone input with volume and EQ controls 5x line input with individual volume control (fader) and gain control 3 master outputs with volume control and EQ settings A good mix between the different inputs and the master volume can be created and EQ settings can be adjusted for each output. In total, you can connect two dynamic microphones and five audio devices, with the microphone inputs equipped with a 3-band EQ control. The gain settings for each input are on the rear panel. This prevents overrides by non-technical users. On the front there is a direct input for 2 microphones, 1 line source or a phone/MP3 device with a special impedance switch.