Peripheral Equipments


Here you will find devices, controllers for adjusting and setting the audio signal and other accessories

TOPSELLER



Topseller

ART PDB4 Four-Channel Passive Direct Box
ART PDB4 Four-Channel Passive Direct Box DetailsThe ART PDB4 Four-Channel Passive Direct Box is a deceptively simple, yet surprisingly useful addition to any serious collection of audio equipment. The PDB4 is a four channel passive direct box that features four quality, fully transformer isolated, direct boxes in a 1U 19-inch rack mount chassis. Inputs and outputs of each of the four channels are isolated to maximize channel separation. Transformer isolation on each output helps to eliminate system ground loops.It is a rock solid, roadworthy interface for connecting outputs of electronic musical instruments (or other audio sources) to the balanced inputs of mixer consoles and other balanced audio products. The PDB4 also allows connection of a music source to an instrument amplifier while simultaneously patching it to a mixer.Electric guitar and bass pick-up output signals, keyboards and line level signals, DJ console output signals, speaker level signals. However you decide to use it, we're sure you'll find the ART PDB4 Four Channel Passive Direct Box to be an indispensable addition to your audio equipment arsenal.ART PDB4 Four-Channel Passive Direct Box FeaturesFour Fully Isolated ChannelsSwitchable Input Attenuation (0dB, -20dB, -40dB)50k Ohm Instrument/Line Input50k Ohm 1/4-inch Parallel Link Jack600 Ohm XLR Output JackSwitchable Ground Lift1U 19-inch Chassis

144,80 €*

Immediately available or ready for collection
ART dual X direct active di box
ART Dualxdirect Active Dual DI Box - fully active design, 18-48V phantom powered or 9V battery powered, converts high-impedance balanced/unbalanced inputs into 600 Ohms balanced outputs, switchable input attenuation (0, -30dB), switchable ground lift, 1/4" TRS/XLR combo connector inputs, balanced XLR outputs, rugged extruded aluminium case. Frequency response: 10Hz-100kHz ± 0.5dB @ +0dBu. THD: 100dB (typical). Channel separation: > 80dB (typical). Maximum input level: +4, +34dBu. Maximum output level: +6dBu (battery powered), +14dBu (phantom powered). Input connections: 1/4" TRS/XLR female balanced/unbalanced (x2), 470k Ohms. Thru connections: 1/4" TRS (2). Output connections: XLR male balanced (x2), < 600 Ohms. Input Attenuation: Switchable, (0, -30 dB), Power Requirements: 9V @ 7.5 mA (battery, alkaline recommended), 18 - 48V DC @ 6.4 mA (phantom power per channel), Dimensions: 99 x 117 x 47mm. Weight: 0.38kg

80,00 €*

delivery time 14 days
ART EQ351 Equalizer
1-channel 31-band graphic equalizer with additional adjustable high and low pass filtersPrecise filters with constant Q-factorBalanced XLR inputs and outputs, active balanced jack inputs and outputs, and unbalanced RCA inputs and outputsInput level control, override indicator and bypass switch with LED indication in each channelLevel adjustment by ± 6 dB or ± 12 dB20 mm frequency band slider with center detentGround Lift SwitchBuilt-in power supply with selectable supply voltageRobust all-metal designDeveloped for years of reliable continuous useTechnical specifications:Controls: power switch, filter area L / R switch, bypass L / R switch, L / R level control, ground lift switchFilter type: constant Q factor, center frequency accuracy 3%Frequency bands: 1 x 31, 1/3 octave, according to ISO standardMaximum gain / reduction: adjustable, ± 6 dB or ± 12 dBTravel of the slider: 20 mm with center catchAdjustable high pass filter: 10 Hz to 250 Hz, 12 dB / octave in each channelAdjustable low-pass filter: 3 kHz to 40 kHz, 12 dB / octave in each channelIndicators Displays for control range (6dB / 12dB), bypass and override indicatorsFrequency range: 20 Hz - 20 kHz, ± 0.5 dBExternal voltage difference: 94 dBDistortion (THD): 0.01%Channel spacing:> 50 dBInputs / Outputs: XLR and 6.3 mm jack (active, balanced), cinch (unbalanced)Maximum input level: +22 dBmInput impedance: 20kOhm (balanced), 15kOhm (unbalanced)Maximum output level: +18 dBm (balanced), +22 dBm (unbalanced)Output impedance: 150 ohmsPower supply: adjustable, 95 - 130 V AC, 50/60 HzPower consumption: 22 VADimensions (W x H x D): 483 mm x 89 mm x 216 mmWeight: 4.1 kg

196,00 €*

delivery time 14 days
ART dual PWM limiter
2-Channel dynamic processorStereo link function of the channelsAdjustable attack and releaseBypass switch per channelGain reduction LED2x Line inputs: XLR and jack, balanced 6.3 mm2x Line outputs: XLR and jack, balanced 6.3 mm2 Loop inputs: 6.3 mm jackDesign: 19" / 1UDimensions (W x H x D): 482.6 x 44.5 x 150 mmWeight: 2.1 kg

259,00 €*

delivery time 14 days
ART EQ341 Equalizer
2-channel 15-band graphic equalizerPrecise filters with constant Q-factorBalanced XLR inputs and outputs, active balanced jack inputs and outputs, and unbalanced RCA inputs and outputsInput level control, override indicator and bypass switch with LED indication in each channelLevel adjustment by ± 6 dB or ± 12 dB20 mm slider with center catchGround Lift SwitchBuilt-in power supply with selectable supply voltageRobust all-metal designDeveloped for years of reliable continuous useTechnical specifications:Controls Power switch, L / R control range switch, L / R bypass switch, L / R level control, Ground Lift switchFilter type constant Q-factor, center frequency accuracy 3%Frequency bands 2 x 15, 2/3 octave, according to ISO standardMaximum amplification / reduction adjustable, ± 6 dB or ± 12 dBTravel of the slider 20 mm with center catchIndicators Displays for control range (6dB / 12dB), bypass and override indicatorsFrequency range 20 Hz? 20 kHz, ± 0.5 dBExternal voltage difference 94 dBDistortion (THD) 0.01%Channel distance> 50 dBInputs / outputs XLR and 6.3 mm jack (active, symmetrical), cinch (unbalanced)Maximum input level +22 dBmInput impedance 20 kOhm (symmetrical), 15 kOhm (unbalanced)Maximum output level +18 dBm (balanced), +22 dBm (unbalanced)Output impedance

173,75 €*

delivery time 14 days
ART Phantom 2 Pro
ART Phantom II Pro, 2-Channel Phantom Power Supply with Battery Support, for up two Condenser Microphones, XLR connectors for balanced inputs and outputs, Low power, high efficiency CMOS circuitry for Long battery life using a standard 9 Volt battery (Alkaline recommended), Can be powered with an external power supply (not included) from AC mains, Rugged extruded aluminum case with accessible battery compartment, LED lighted On/Off switch, Low noise, low distortion circuitry

108,00 €*

Immediately available or ready for collection
ART Z-Direct passive DI BOX
Passive DI BoxFrequency range: 10 Hz -50 kHzTHD: 0.01% Typical @ 1 kHzInput: unbalanced jackInput impedance 50 OhmOutput: XLR maleOutput impedance 600 OhmSwitchable low pass filter -3 dB @ 30 kHzPAD switch (0dB, -20dB, -40dB)Phase switch (normal / invert)Switchable ground liftDimensions: 44.5 x 107 x 89 mmWeight: approx. 340 g

46,25 €*

Immediately available or ready for collection
ART PDB Passive Direct Box
The PDB™ Passive Direct Box is a rock solid, roadworthy DI for connection of the outputs of electronic musical instruments (or other audio sources) to the balanced inputs of mixer consoles and other balanced inputs.The PDB™ also allows connection of a music source to an instrument amplifier while simultaneously patching it to a mixer.PDB Applications:Electric guitar and bass pick up output signals – The high impedance signal from a guitar or bass guitar pickup is translated by the PDB™ into a low impedance balanced signal required by mixing consoles.Keyboards and line level signals – The PDB™ automatically balances and matches the line level outputs of modern electronic keyboards. If you are using a multiple keyboard setup and your keyboards are all plugged into a single instrument amplifier, the PDB™ can be used to replace individual direct boxes. Simply send the output of the instrument amplifier to the PDB™ and then to the console (instead of a separate DI box for each keyboard).DJ console output signals – DJ mixers often supply only an unbalanced -10dB signal. The PDB™ converts this signal to a balanced line level signal before it reaches the console, while providing a convenient method of connector transition with the capability to run long cables.Speaker level signals – The PDB’s ability to accept speaker level inputs from a power amplifier’s output allows post-amplifier, post eq and effects signals to be fed directly to the console. In this manner, a particular effect or amplifier sound can be sent directly to the mix.SpecificationsFrequency Response: 10 Hz – 50 kHz +/- 0.5dB @ +4dBuOutput Connections: 600 O XLR Output JackGround Lift: SwitchableInput Attenuation: Switchable (0dB, -20dB, -40dB)Instrument Input: 50k OParallel Link Jack: 50k ODimensions: 3" x 5" x 2"

51,00 €*

Immediately available or ready for collection
ART DTI Dual Transformer/Isolator
ART DTI Dual Transformer/Isolator - a high quality, totally passive audio interface that uses a pair of high performance transformers to totally separate input and output signal grounds, thereby isolating two systems and reducing hum and ground-loop noise. The DTI's audio transformers have an extremely flat and wide frequency response and can handle high signal levels while maintaining an isolated balanced output. This gives the DTI a very clean and neutral sound with a wide variety of signal sources. The transformers are wound for 1:1 unity gain and are designed to be used with impedances from 600 Ohms to 100 kOhms, Input Connections: XLR female balanced, 1/4" TRS, unbalanced, and RCA type phono jacks, Output Connection: XLR male balanced, 1/4" TRS, unbalanced, and RCA type phono jacks, Dimensions 44.5mm x 107mm x 89mm, Weight 0,34 kg

85,00 €*

delivery time 14 days
ART active Xdirect Di box
Active DI BoxFrequency range: 10 Hz –100kHzMax. output level: +6 dBu (battery powered) / +14 dBu (phantom powered)Max. input level: +4/+24/+44 dBuDynamic range: > 100 dBInput: Jack and XLR femaleInput impedance 470 OhmOutput: XLR maleOutput impedance

61,00 €*

delivery time 14 days
ART DPDB dual passive direct BOX
736/5000Passive DI boxThe dPDB Passive DI Box has two high-quality DI boxes in a portable housing. It is used for balancing unsymmetrical signals e.g. from line instruments such as bass, guitar or keyboards. It converts the high-impedance signals of the instruments into low-impedance balanced signals, which are necessary for mixing consoles. The dPDB has a switchable input attenuation (0dB, -20dB, -40dB), a 50k Ohm instrument input, a 50k Ohm parallel link socket, a 600 Ohm XLR output and a switchable ground lift.Characteristics:• Frequency response: 10 Hz - 50 kHz +/- 0.5dB @ + 4dBu• Connectors: 600 Ohm XLR Output Jack• Ground Lift Switchable• Input Sensitivity: Switchable (0dB, -20dB, -40dB)

70,00 €*

delivery time 14 days
ARTSplitMix4 Splitter/Mixer
Splitter / Mixer4-channel passive mixer4 stereo input channelsstereo output (all 6.3 mm jack connectors are stereo -tip, ting, sleeve)Dimensions: 47 x 117 x 104 mm

88,00 €*

Immediately available or ready for collection
ART EQ355 Equalizer
2-channel 31-band graphic equalizer with additional adjustable high and low pass filtersPrecise filters with constant Q-factorBalanced XLR inputs and outputs, active balanced jack inputs and outputs, and unbalanced RCA inputs and outputsInput level control, override indicator and bypass switch with LED indication in each channelLevel adjustment by ± 6 dB or ± 12 dB20 mm frequency band slider with center detentGround Lift SwitchBuilt-in power supply with selectable supply voltageRobust all-metal designDeveloped for years of reliable continuous useTechnical specifications:Controls: power switch, filter area L / R switch, bypass L / R switch, L / R level control, ground lift switchFilter type: constant Q factor, center frequency accuracy 3%Frequency bands: 2 x 31, 1/3 octave, according to ISO standardMaximum gain / reduction: adjustable, ± 6 dB or ± 12 dBTravel of the slider: 20 mm with center catchAdjustable high pass filter: 10 Hz to 250 Hz, 12 dB / octave in each channelAdjustable low-pass filter: 3 kHz to 40 kHz, 12 dB / octave in each channelIndicators Displays for control range (6dB / 12dB), bypass and override indicatorsFrequency range: 20 Hz - 20 kHz, ± 0.5 dBExternal voltage difference: 94 dBDistortion (THD): 0.01%Channel spacing:> 50 dBInputs / Outputs: XLR and 6.3 mm jack (active, balanced), cinch (unbalanced)Maximum input level: +22 dBmInput impedance: 20kOhm (balanced), 15kOhm (unbalanced)Maximum output level: +18 dBm (balanced), +22 dBm (unbalanced)Output impedance: 150 ohmsPower supply: adjustable, 95 - 130 V AC, 50/60 HzPower consumption: 22 VADimensions (W x H x D): 483 mm x 89 mm x 216 mmWeight: 4.1 kg

311,25 €*

delivery time 14 days
dbx 1231 graphic equalizer 2x 31-band
DBX 12312x 31-Band Graphic EQ4 LED display indicators45mm Faders (20Hz - 20kHz)Range +/- 6dB und +/- 15dBbalanced 1/4" jack and XLR inputs/outputs.Size: 19"/3U

561,00 €*

delivery time 14 days
Dbx ZC2 Remote
DBX DriveRack 260, 220i and ZoneProVolume control and mute switchConnection via Cat 5 cable

86,00 €*

delivery time 14 days
Dbx ZC6-EU Wall mounted Zone Controller
Wall-Mounted Zone ControllerPush Button Up/Down ControllerUP / DOWN function for volume etc. of the ZonePro series.Connection ivia CAT5 cable with RJ-45 plug.

86,00 €*

delivery time 14 days
dbx 286S mic preamp/processor with dynamics
The dbx 286S is a full featured Channel Strip Processor that delivers a studio quality microphone/instrument preamplifier and four processors that can be used independently or in any combination. The dbx 286s Mic Preamp has all the features you need, including wide-ranging input gain control, switchable +48V phantom power, and an 80Hz high-pass filter to remove low frequency hum, rumble or wind. Use the patented dbx OverEasy compressor to transparently smooth out uneven acoustic tracks or deliver that classic "in your face" vocal performance that only a dbx compressor can. Eliminate vocal sibilance and high frequency distortion from instruments such as cymbals with the frequency tunable De-Esser. Fine-tune the Enhancer HF Detail control to add sparkle and crispness to your tracks and make adjustments to the LF Detail control to add fullness and depth to vocals and bass instruments while cleaning up the muddy low midrange frequencies. And, the separate threshold and ratio controls on the Expander/Gate allow you to subtly reduce headphone leakage or radically gate noisy guitar amps.The dbx 286s offers a full compliment of metering and status LEDs to visually guide you to achieving the right sound. The floating balanced XLR Mic Input accepts balanced or unbalanced inputs to easily connect to professional and home studio microphones. The additional 1/4" TRS Line Input can accept balanced/unbalanced signals to process live electronic instruments or pre-recorded tracks at mixdown. Use the Insert jack to interface between the Mic Preamp and the signal processing sections to "loop out" to external processors (such as EQ or delay unit) or to mix the Mic Preamp's signal out to an external destination.

234,00 €*

delivery time 14 days
dbx DriveRack 4820
48 and 96 kHz operationColor QVGA Display4 analog and AES/EBU inputs8 analog and AES/EBU outputsOptional CobraNet I/OOptional Jensen® I/O TransformersFull Bandpass Filter, Crossover andRouting Configurations with Bessel,Butterworth, and Linkwitz-Riley filters31-Band Graphic and 9-bandParametric EQ on every input6-band Parametric EQ on every outputLoudspeaker Cluster and DriverAlignment DelaysSelectable DSP inserts on all inputsand outputs including Classic dbxCompression, Limiting and AdvancedFeedback Suppression among othersEthernet networking controldbx ZC wall panel control

3 915,00 €*

delivery time 14 days
dbx CT3 Advance Cable Tester
The dbx CT3 is an advanced cable testing unit allowing you to evaluate a large variety of cables with ease. The CT3 offers many common connectors such as RJ45, RJ11, MIDI, Speaker Twist, XLR, RCA Phono, BNC, DIN, TRS, TS, DMX, & Banana. It can be split into 2 parts, a SENDER and RECEIVER so preinstalled and long cables can be tested.Recommended for: Studio, Tour, Portable. FeaturesTests up to 8-pin cables2 piece chassis for testing installed cablesTest Tone GeneratorAllows connection between different format connectors with ease‘Banana’ connector continuity tester with beeper and LED indicatorSuper-rugged construction for durability and longer life(2) DMX (5-pin) connectors for testing of 5 pin->to pin connections(2) BNC connectors for testing of 2 pin->to pin connections(2) RCA Phono connectors for testing of 2 pin->to pin connections(2) XLR connectors (1 x Male, 1 x Female) for testing of 3 pin->to pin connections(2) MIDI (5-pin DIN) connectors for testing of 5 pin->to pin connections(2) Speaker Twist connectors for testing of 4 pin->to pin connections(2) Banana connectors for testing of 1 pin->to pin connections(2) 1/4" (6.3mm) TRS/TS connectors for testing of 3 pin->to pin connections(2) RJ45 connectors for testing of 8P8C modular connections(2) 1/8" (3.5mm) TRS/TS connectors for testing of 3 pin->to pin connections

213,00 €*

Immediately available or ready for collection
dbx DriveRack PA2
DBX DRIVERACK PA2digital speaker management system31 Band grafic equalizerparametric 8-Band input-EQ with auto EQ function, peak stop limitercrossovercompressorsubharmonic synthesizeroutput-delay up to 3,4 m/10 ms,input-delay up to 34 m/100 msfeedback-destroyer with 12x notch-filters 1/80 octaveparametric 8-band output-EQ also for speaker tuningsthird-band real time analyzerpink noise generatorremote control with Mac/Windows/Android/iOS2x XLR input,1x XLRwith 48V phantom power for optional measurement microphone6x XLR male outputsethernet connectorUSB connector19" 1U

539,00 €*

Delivery time from 6 to 8 weeks!

TOP MARKEN


Thumbnails
Thumbnails