Amplifiers


The amplifiers are used to amplify the audio signal for driving the loudspeakers

TOPSELLER



Topseller

QPRO Audio 2 channel amplifier 1HE 2 x 4760W/2Ohm
The QLP - Series amplifiers are digital two channel amplifiers with power factor correction technology.All QLP models have a very high-efficient switch mode power supply, which ensures best and stableperformance even at full power.Our digital amplifier msv technology, together with the use of best selected electronic components allows the 2 Ohmuse of all four channels at same time with a maximum power of 2 x 4760 watts, packed in a lightweight andcompact size of 1U.The QLP-Series is equipped with a switch msv on the back panel to adjust the Input gain to 29dB, 32dB, 35dB and38dB to match with other devises.Four SPEAKON outputs are mounted at the rear side. The SPEAKON connector of the output channel A (1+/1-) isconnected with all four poles and offers the output signal of channel B at the pins 2 (+/-). This four-pole connection makes it easy to connect a Sub / Sat system with onecable only.The QLP-Series can be switched into msv stereo, mono and bridge mode. In mono mode the input signal fromchannel A is linked to the output channel A + B. In bridget mode theconnection is 1+/2- on output A. The Clip limiter can be switched On/Off on all channels.Rated Output Power (THD + N= 1%, 1KhZ contiune sine wave, all channel driving): 8 Ohm / Stereo: 2 x 1000W4 Ohm / Stereo: 2 x 1700W2 Ohm / Stereo*: 2 x 4760W16 Ohm / Bridge: 1 x 2000W8 Ohm / Bridge: 1 x 3400W4 Ohm / Bridge*: 1 x 5780WOutput RMS voltage (THD+N=1%,1kHz): 89,4VSlew rate (1kHz, Low-pass filter msv bypassed): 50V7usSensitivity (Rated Power, 1kHz): Selectable 38dB, 35dB, 32dB, 29dBTHD+N(10% Rated Power, typical): 0,01%IMD-SMPTE(10% Rated Power,typical): 0,01%DIM30(10% Rated Power, typical): 0,01%Cross-talk(20Hz-1kHz,below Rated Power): >=90dBFrequency response(10% Rated Power,20Hz-20kHz,8Ohm): +-0,2dBInput impedance: 20k Ohm (Balance), 10kOhm (unbalance)Damp factor(8Ohm,20Hz-200Hz): >=5000SNR(A weighted 20Hz-22kHz): >=107dBMain power: 90 - 260 VAC, 50-60HzProtection: Under voltage, msv DC, Over temperature, Over load limiter, Short protection.Size(W×H×D): 483x45x370mmNet weight: 9kg*Test condition: 20ms,1kHz,THD+N=1%.

€2,299.00*

delivery time 7 days
Crown XLS 2002 Amplifier 2x 650 Watt/4 Ohm
CROWN XLS 2002 digital amplifier with class D amplifier circuit2x 1.050 watts @ 2 ohms2x 650 watts @ 4 ohms2x 375 watts@ 8 ohmsbridged 1x 2.100 watts @ 4 ohms, monobridged 1x 1.300 watts @ 8 ohms, monoHigh and low pass filter per channelSleep mode with external triggerPeakX limiterVery silent, temperature-dependent fanDamping factor> 2001.4 and 0.775 volts input sensitivityInputs: XLR, Jack, RCA per channelOutputs: Speakon, screw terminals per channelHeight: 2UDepth: 27.2 cm4.9 kgTop Features:New is the energy management. Due to recovering energy the Crown XLS amplifier operates very efficiently. Therefore it is more efficient than conventional amplifiers. Another new feature is the sleep mode and a power trigger for external switch on and off.The large display shows clearly all parameters. The Blackout function, new menus and lockout mode make the operation easy and safe.

€599.00*

Immediately available or ready for collection
Yamaha Px5 Amplifier - 2x 500watts/8ohm
Yamaha PX5Power:2 x 800 W / 4 Ohm,2 x 500 W / 8 Ohm,1 x 800W 8 Ohm Bridge,1 x 1400W 4 Ohm BridgeSpeaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 6.9 kg

€949.00*

Immediately available or ready for collection
Crown XLS XLS 1002 Amplifier 2x 350 Watt/4 Ohm
With Class-D circuitPower: 2x 550 Watt / 2 Ohm, 2x 350 Watt / 4 Ohm, 2x 215 Watt / 8 Ohm, bridged 1x 1100 Watt / 4 Ohm, bridged 1x 700 Watt / 8 OhmAmplifier modes: 2-channel stereo, mono bridged or Y mode24 dB Linkwitz-Riley crossoverInput Sensitivity 1.4 or 0.775 VLarge front display for easy operationBlack-Out mode automatically switches off the displayLock-out mode against incorrect operationRemote power for remotely turning on and offPeakX limiter per channelQuiet, temperature controlled fanRugged metal housing5 status LEDs per channelConnections: XLR, jack and RCA inputs, 2x Speaker Twist and screw outputsDesign: 19" / 2UDepth: 19.6 cmWeight: 3.9 kg

€459.00*

Immediately available or ready for collection
Denon Pro DN-280 Zone Amplifier with Microphone Input
If you need a compact, high-powered amplifier that sums stereo signals into a mono output for paging, P.A. announcements and background music applications, the Denon Professional DN-280 is the ideal solution. With a space-saving, one-half rack space profile, the DN-280 features a microphone input for paging, a front panel 3.5mm (1/8-inch) AUX input and stereo analog inputs (summed to MONO) for signals from external playback devices such as an iPhone or stereo tuner.The amplifier handles a 4O load or 70V/100V speaker runs, perfect for multiple speaker setups in small retail stores or doctor’s offices. A cool-running, powerful Class D amplifier delivers 100 watts with 95dB, ensuring extremely clean performance under all conditions. The DN-280 has built-in short circuit protection and front-panel LED indicators for signal present, clipping status and thermal interruption.Class D 100W mono amplifierTrim one-half rackspace height - rackmountable or stand-aloneRemovable feet and option to mount two units together in a 1RU spacePaging microphone input with gain controlTone and master volume controlsRCA inputs (L/R stereo inputs summed to MONO)3.5mm (1/8”) AUX input70V/100V/4O Euroblock outputTotal Harmonic Distortion: 95dB (A-weighted)Damping Factor: >200 (1k 8O)Output Power: 60WConnectors(1) Euroblock channel output(1) Dual RCA input(1) XLR / TRS 1/4” (6.35mm) combination input(1) TRS 1/8” (3.5mm) auxiliary inpuInput SensitivityDual RCA input: 0+/-1dBvAuxiliary input: -10+/-1dBvCombination input: -30+/-1dBvInput Impedance: 20kO balanced or 10kO unbalancePower100V ~, 50/60Hz, 100W110–120V ~, 50/60Hz, 100W220–240V ~, 50/60Hz, 100WVoltage Gain: 40+0/-1dB (100V)Dimensions (width x depth x height): 7.9” x 10.7” x 1.7” (200 x 273 x 43mm)Weight: 5.3 lbs. (2.4kg)

€299.00*

delivery time 14 days
Crown XLS XLS 2502 Amplifier 2x 775 Watt/4 Ohm
CROWN XLS 2502 digital amplifier with class D amplifier circuit2x 1.200 watts @ 2 ohms2x 775 watts @ 4 ohms2x 440 watts@ 8 ohmsbridged 1x 2.400 watts @ 4 ohms, monobridged 1x 1.550 watts @ 8 ohms, monoHigh and low pass filter per channelSleep mode with external triggerPeakX limiterVery silent, temperature-dependent fanDamping factor> 2001.4 and 0.775 volts input sensitivityInputs: XLR, Jack, RCA per channelOutputs: Speakon, screw terminals per channelHeight: 2UDepth: 27.2 cm4.9 kgTop Features:New is the energy management. Due to recovering energy the Crown XLS amplifier operates very efficiently. Therefore it is more efficient than conventional amplifiers. Another new feature is the sleep mode and a power trigger for external switch on and off.The large display shows clearly all parameters. The Blackout function, new menus and lockout mode make the operation easy and safe.

€719.00*

Immediately available or ready for collection
American Audio VLP300 power amplifier
Output Power:- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD- Bridge Mode, Mono 300W RMS @ 8 Ohms, 1K Hz, 1% THD^- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)- Class D- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz- Slew Rate: 15V Per usec- Damping Factor: @ 8 Ohm: 260- Impedance: 20 Ohms balanced / 10 Ohms unbalanced- Cooling System: 2 indivdual fans- Special Features: High/Low Pass Filter/Input Sensitivity Selector/Ground Lift- Input: XLR 3pin + Jack 6,3mm- output: Speaker + Binding post- Dimensions (LxWxH): 336 x 482 x 44mm 1-rack mount space- Weight: 24 lbs.(11kg)

€289.00*

Immediately available or ready for collection
Linea Research 44 M Dante Card
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

€799.00*

delivery time 7 days
Linea Research 44 M20 Dante 4 channel amplifier with on-board DSP with Dante
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 5000W / 2 ohms, 4 x 3000W / 4 ohms, 4 x 1500W / 8 ohms2 x 10000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In and Dante compatible4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Dante network audio interfaceGrouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

€7,110.00*

delivery time 7 days
Yamaha Px10 Amplifier - 2x 1000watts/8ohm
Yamaha PX10Power:2 x 1200 W / 4 Ohm,2 x 1000 W / 8 Ohm,Speaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 7,4 kg

€1,198.00*

Immediately available or ready for collection
QPRO Audio 4 channel amplifier 1HE 4 x 600W/8Ohm
The QLE series amplifiers are 2 or 4 channel amplifiers.All models have a highly efficient switching power supply, which ensures that QLE amplifiers run optimally and stably even at full power.Our digital amplifier technology, msv combined with the use of the best selected electronic components, enables 4 ohms to be used simultaneously on all two or four channels with maximum performance. Packed in a lightweight and compact 1U size.The QLE series is equipped with a switch on the back to adjust the input sensitivity of 0.7 V or 1 V.Nominal output power (THD + N = 1%, msv continue 1 kHz sine wave, control all channels)Rated Output Power(THD+N= 1%,1kHz continue sine wave, all channel driving)8Ohm Stereo: 4x600W4Ohm Stereo: 4x900W16Ohm Bridge: 2x1200W8Ohm Bridge: 2x1800WOutput RMS voltage: 693VSensitivity: 1 Vrms , 0.7 Vrms (msv Rated Power,1kHz)THD+N: 0.05% (10% Rated Power, typical)Cross-talk: >=75dB (20Hz-1kHz,below Rated Power)Frequency response: +-0.2dB (10% Rated Power,20Hz-20kHz,8 )Input impedance: 20k Balance 10k UnbalanceDamp factor: >=1000(8Ohm ,20Hz-200Hz)SNR: >=100dB(A weighted 20Hz-20kHz)Main power: 220VAC 10 (+- % )50/60HzProtection: Under voltage, DC, Over msv temperature, Over load limiter, Short protection.Size(W×H×D): 480x45x352mmNet weight: 6,8kg

€1,199.00*

Immediately available or ready for collection
Yamaha Px8 Amplifier - 2x 800watts/8ohm
Yamaha PX8Power:2 x 1050 W / 4 Ohm,2 x 800 W / 8 Ohm,Speaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 7,2 kg

€1,049.00*

Immediately available or ready for collection
Crown XTi 1002 Amplifier 2x 500 Watt/4 Ohm
Crown Xti 1002, DSP control amplifier, 19" 2 U, 2x 700 W (2 Ohm), 500 W (4 Ohm), 275 W (8 Ohm), 1000 W Bridge 8 Ohm, 1400 Watt Bridge 4 Ohm, DSP-Control: Input EQ with 6 parametric Filters per channel with adjustable Q-Shelf and +/- 15 dB Gain, Crossover with High- and Lowpass, per channel with 6/12/18/24 dB per Octave and switchable polarity, Output EQ with 8 parametric Filters per channel with adjustable Q-Faktor and +/- 15 dB Gain, Delay up to 50 ms, Subharmonic Synth, Peak Plus Limiter with adjustable Threshold, Attack and Release, 50 Presets, 3 mode switchable cooling fan, HiQnet Band Manager and System Artchitect Software control by USB-Port Type B, display with temperature of powersupply and voltage, 2x NL 4 Speakon out, Binding Post out, XLR in/out, dimensions: 19" (485mm) x 2 U (89mm) x 311 mm, weight 8,4 Kg

€679.00*

Immediately available or ready for collection
Linea Research 44 M06 4 channel amplifier
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 1500W / 2 ohms, 4 x 1500W / 4 ohms, 4 x 1500W / 8 ohms2 x 3000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

€4,680.00*

delivery time 7 days
Linea Research 44 M10 4 channel amplifier
4-channel Class-D high-performance amplifier with switched-mode power supply4 x 2500W / 2 ohms, 4 x 2500W / 4 ohms, 4 x 1500W / 8 ohms2 x 5000W / 4 Ohm bridge4 x Analog In, 2 x AES3 In 4 x 4 DSP controllers including linear phase filter, FIR filter and multiband limiting (96kHz / 40 bit float)Grouping functions and multi-layer EQVery comprehensive monitoring with a non-volatile log functionFlexible input current limitationOversized universal power supplyOperation via Ethernet or front panelManufactured in UK

€5,520.00*

delivery time 7 days
Crown XLS XLS 1502 Amplifier 2x 525 Watt/4 Ohm
CROWN XLS 1502 digital amplifier with class D amplifier circuit2x 775 watts @ 2 ohms2x 525 watts @ 4 ohms2x 300 watts@ 8 ohmsbridged 1x 1550 watts @ 4 ohms, monobridged 1x 1050 watts @ 8 ohms, monoHigh and low pass filter per channelSleep mode with external triggerPeakX limiterVery silent, temperature-dependent fanDamping factor> 2001.4 and 0.775 volts input sensitivityInputs: XLR, Jack, RCA per channelOutputs: Speakon, screw terminals per channelHeight: 2UDepth: 19.6 cm3.9 kgTop Features:New is the energy management. Due to recovering energy the Crown XLS amplifier operates very efficiently. Therefore it is more efficient than conventional amplifiers. Another new feature is the sleep mode and a power trigger for external switch on and off.The large display shows clearly all parameters. The Blackout function, new menus and lockout mode make the operation easy and safe.

€569.00*

delivery time 14 days
QPRO Audio 2 channel amplifier 1HE 2 x 800W/8Ohm
The QLE series amplifiers are 2 or 4 channel amplifiers.All models have a highly efficient switching power supply, which ensures that QLE amplifiers run optimally and stably even at full power.Our digital amplifier technology, msv combined with the use of the best selected electronic components, enables 4 ohms to be used simultaneously on all two or four channels with maximum performance. Packed in a lightweight and compact 1U size.The QLE series is equipped with a switch on the back to adjust the input sensitivity of 0.7 V or 1 V.Nominal output power (THD + N = 1%, continue 1 kHz sine wave, control all channels)Rated Output Power(THD+N= 1%,1kHz continue msv sine wave, all channel driving)8Ohm Stereo: 2x800W4Ohm Stereo: 2x1200W16Ohm Bridge: 1x1600W8Ohm Bridge: 1x2400WOutput RMS voltage: 80.0VSensitivity: 1 Vrms , 0.7 Vrms (Rated Power,1kHz)THD+N: 0.05% (10% Rated Power, typical)Cross-talk: >=75dB (20Hz-1kHz,below Rated Power)Frequency response: +-0.2dB (10% Rated msv Power,20Hz-20kHz,8 )Input impedance: 20k Balance 10k UnbalanceDamp factor: >=1000(8Ohm ,20Hz-200Hz)SNR: >=100dB(A weighted 20Hz-20kHz)Main power: 220VAC 10 (+- % )50/60HzProtection: Under voltage, DC, Over msv temperature, Over load limiter, Short protection.Size(W×H×D): 480x45x352mmNet weight: 5,9kg

€879.00*

Immediately available or ready for collection
American Audio VLP600 power amplifier
Output Power: - 300W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD 200W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD - Bridge Mode, Mono 600W RMS @ 8 Ohms, 1K Hz, 1% THD - Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)- Class D - Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz - Slew Rate: 15V Per usec - Damping Factor: @ 8 Ohm: 300 - Impedance: 20 Ohms balanced / 10 Ohms unbalanced - Cooling System: 2 indivdual fans - Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift Limiter - build in clip limiter - Input: XLR 3pin + Jack 6,3mm - output: Speaker + Binding post - Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces - Weight: 33 lbs. / 15 Kgs.

€379.00*

Immediately available or ready for collection
Crown XTi 2002 Amplifier 2x 800 Watt/4 Ohm
Crown Xti 1002, DSP control amplifier, 19" 2 U, 2x 1000 W (2 Ohm), 800 W (4 Ohm), 475 W (8 Ohm), 1600 W Bridge 8 Ohm, 2000 Watt Bridge 4 Ohm, DSP-Control: Input EQ with 6 parametric Filters per channel with adjustable Q-Shelf and +/- 15 dB Gain, Crossover with High- and Lowpass, per channel with 6/12/18/24 dB per Octave and switchable polarity, Output EQ with 8 parametric Filters per channel with adjustable Q-Faktor and +/- 15 dB Gain, Delay up to 50 ms, Subharmonic Synth, Peak Plus Limiter with adjustable Threshold, Attack and Release, 50 Presets, 3 mode switchable cooling fan, HiQnet Band Manager and System Artchitect Software control by USB-Port Type B, display with temperature of powersupply and voltage, 2x NL 4 Speakon out, Binding Post out, XLR in/out, dimensions: 19" (485mm) x 2 U (89mm) x 311 mm, weight 8,4 Kg

€759.00*

Delivery time from 10 to 12 weeks!
Yamaha Px3 Amplifier - 2x 300watts/8ohm
Yamaha PX3Power:2 x 500 W / 4 Ohm,2 x 300 W / 8 Ohm,1 x 600W 8 Ohm Bridge,1 x 1000W 4 Ohm BridgeSpeaker presets allow optimal speaker performance DSP features including D-ContourProcessing Input: XLR + jackOutput: Speaker twist, jack, clamp connectionDimensions (W x H x D): 480 x 88 x 388 mm Construction: 19 "/ 2UWeight: 6.9 kg

€798.00*

Immediately available or ready for collection

TOP MARKEN


Thumbnails
Thumbnails